Attached Files
-
Vinklad.jpg 18.23KB
1 downloads
Portning Av Tb
Started by
clipping_point
, Nov 27 2004 03:15 PM
115 replies to this topic
#1
clipping_point
-
-
- 4,908 posts
Scary Internerd
- Location:Linköping, Sweden
Posted 27 November 2004 - 03:15 PM
Så här der det ut nu. Små bullar som kanske är till för att göra det hela mer lättreglerat
#2
clipping_point
-
-
- 4,908 posts
Scary Internerd
- Location:Linköping, Sweden
Posted 27 November 2004 - 03:19 PM
En portad variant, Vocky har gjort nåt liknande
Attached Files
-
Portad.jpg 7.74KB
0 downloads
#3
clipping_point
-
-
- 4,908 posts
Scary Internerd
- Location:Linköping, Sweden
Posted 27 November 2004 - 03:21 PM
Så här blir resultatet
#4
skogshuggarn
-
-
- 1,088 posts
Need to get Out More
- Location:Sweden
- Interests:weightlifting and spending money on my car
Posted 27 November 2004 - 04:11 PM
Här kommer ett gäng bilder på hur orginal ser ut.
I utgångspossition så ligger inte spjället plant, vilket man kanske tror... det ligger an mot ena väggen.
Attached Files
-
PICT0007.JPG 66.83KB
1 downloads
#5
skogshuggarn
-
-
- 1,088 posts
Need to get Out More
- Location:Sweden
- Interests:weightlifting and spending money on my car
#6
skogshuggarn
-
-
- 1,088 posts
Need to get Out More
- Location:Sweden
- Interests:weightlifting and spending money on my car
#7
skogshuggarn
-
-
- 1,088 posts
Need to get Out More
- Location:Sweden
- Interests:weightlifting and spending money on my car
#8
skogshuggarn
-
-
- 1,088 posts
Need to get Out More
- Location:Sweden
- Interests:weightlifting and spending money on my car
Posted 27 November 2004 - 04:15 PM
undersidan oxå...
Attached Files
-
PICT0010.JPG 72KB
0 downloads
#9
skogshuggarn
-
-
- 1,088 posts
Need to get Out More
- Location:Sweden
- Interests:weightlifting and spending money on my car
#10
clipping_point
-
-
- 4,908 posts
Scary Internerd
- Location:Linköping, Sweden
Posted 27 November 2004 - 05:42 PM
Börjar närma mig det verkliga utseendet
Attached Files
-
Spj_ll2.jpg 18.78KB
0 downloads
#11
clipping_point
-
-
- 4,908 posts
Scary Internerd
- Location:Linköping, Sweden
Posted 27 November 2004 - 05:44 PM
Å den moddade, frågan är hur mkt det ger. Det kanske räcker att "platta till" axeln
Attached Files
-
Spj_ll2moddad.jpg 7.68KB
0 downloads
#12
skogshuggarn
-
-
- 1,088 posts
Need to get Out More
- Location:Sweden
- Interests:weightlifting and spending money on my car
Posted 28 November 2004 - 06:24 AM
Börjar närma mig det verkliga utseendet
när du får tillbaka ditt o ser de i verkligheten kommer du garva gött åt bilderna 
#13
skogshuggarn
-
-
- 1,088 posts
Need to get Out More
- Location:Sweden
- Interests:weightlifting and spending money on my car
Posted 28 November 2004 - 06:35 AM
Här kommer en liten skiss av hur TB ser ut...
...och nej, jag är inte 4 år, bara en övertrött nattarbetare 
Attached Files
-
PICT0015.JPG 40.59KB
0 downloads
#14
clipping_point
-
-
- 4,908 posts
Scary Internerd
- Location:Linköping, Sweden
Posted 28 November 2004 - 09:05 AM
Om man vrider spjället i din figur ser det inte ut att hända nästan nåt med flödet det första 1/4-varvet. Undrar vad som händer om man börjar rymma upp i en sån känslig installation.
#15
vocky
-
-
- 11,969 posts
Moderator
- Gender:Male
- Location:Earth
Posted 28 November 2004 - 09:46 AM
Good pictures, you can see what I mean about the shape, not perfect for best flow.
I will try to get some pics of mine on this thread.
Also tried yesterday to see if my z22se had a flat spot @3000rpm, but could not notice any flat spot at all, does this only show up on a rolling road?
#16
clipping_point
-
-
- 4,908 posts
Scary Internerd
- Location:Linköping, Sweden
Posted 28 November 2004 - 10:35 AM
It seems that the flow increases very gradually the first 20° of turning of the butterfly disc. If this is changed drastically then it could confuse the electronical control, I guess.
The safest would to be only opening up at the max point, by flattening the shaft and enhancing the flow into the TB, I guess?
#17
clipping_point
-
-
- 4,908 posts
Scary Internerd
- Location:Linköping, Sweden
Posted 28 November 2004 - 10:47 AM
New sketch (have sent my own TB away so I´m only guessing, I´m afraid 
Attached Files
-
Spj_ll_verklig.jpg 13.29KB
0 downloads
#18
Guest_Guest (Guest)
Guest_Guest (Guest)
Posted 28 November 2004 - 10:48 AM
Yes, I once polished a weber twin choke in that area and the engine raced away 
, luckily the tickover screw saved the day, lesson learn't 
.
The shaft is in the highest flow part, so reducing that piece gives more gains, the new screws I used are flush with the flat section, I also flattened the other side of the shaft slightly.
There is room for improvement on the body itself, I will get pics later
, luckily the tickover screw saved the day, lesson learn't .
The shaft is in the highest flow part, so reducing that piece gives more gains, the new screws I used are flush with the flat section, I also flattened the other side of the shaft slightly.
There is room for improvement on the body itself, I will get pics later
#20
vocky
-
-
- 11,969 posts
Moderator
- Gender:Male
- Location:Earth
Posted 28 November 2004 - 10:55 AM
why did it log me out
anyway a bit like this,
anyway a bit like this,
0 user(s) are reading this topic
0 members, 0 guests, 0 anonymous users
